![fox float rp23 ml175 fox float rp23 ml175](https://www.rczbikeshop.com/media/catalog/product/cache/36/image/480x/602f0fa2c1f0d1ba5e241f914e856ff9/p/h/photo-29145.jpg)
The shock received mixed reviews and was quickly replaced by the successful Fox Float RP3 in 2005. Their first try with rear platform shocks was the Fox Float AVA in 2004. With the introduction of stable platform shocks by its competitors, it did not take long for Fox to launch its equivalent. It started building its first bicycle shock for Cannondale in 1993 and has dominated the bicycle rear shock market ever since. It has been in the suspension business for 30 years, building shocks for the motorcycle industry initially. The ProPedal knob clicks twice per setting as it turns.Fox Racing Shox is a company that needs little introduction. Turn the ProPedal knob clockwise (relative to the ProPedal knob facing the user) until the selection you want-1, 2, or 3-is aligned with the ProPedal lever ( #3 ). How do you turn the propedal knob on drcv? Pressurize your main air chamber to a minimum of 50 psi and no more than 300 psi. Check that all parts of the shock are clear of the frame and swingarm as it cycles through the travel. What should the air pressure be on a float rp23 Fox?Ĭarefully cycle the suspension through its entire travel. It should only be adjusted while in a stationary position. The ProPedal knob should NOT be adjusted on-the-fly. Push the ProPedal knob into its new position (#4).
![fox float rp23 ml175 fox float rp23 ml175](https://ae01.alicdn.com/kf/HTB16bVOIXXXXXajXpXXq6xXFXXXa/GIANT-ANTHEM-X-FR-4-0-Frame-26-M-18-w-FOX-FLOAT-RP23-Smoke-Blue.jpg)
The first click occurs as you exit the current setting the second click as you engage the new setting. The ProPedal knob clicks twice per setting as it turns. How does the propedal knob work on a float? Turn the ProPedal knob clockwise (relative to the ProPedal knob facing the user) until the selection you want-1, 2, or 3-is aligned with the ProPedal lever (#3). Lift the ProPedal knob (see frame #2in the drawing below). To adjust the ProPedal knob: Turn the ProPedal lever to the PROPEDALposition, as shown in graphic above. How do you adjust the propedal Knob in rp23? What PSI is Fox DPX2?ĭo not exceed maximum air pressure: FLOAT DPS and DPX2 air shocks have a maximum air pressure of 350 psi. How much air should I put in my FOX shock?Īdd air pressure to the main air chamber in ~50 psi (3.4 bar) increments, slowly cycling the shock after every 50 psi (3.4 bar) addition. Add air pressure until desired pressure is shown on the gauge. Screw the FOX Racing Shox High Pressure Pump onto the air valve until the pump shows pressure on the gauge. Setting Sag Locate the Schrader air valve on the shock and remove the air valve cap. Do not exceed the maximum FLOAT air pressure! Remove the pump. This will equalize the positive and negative air chambers and will change the pressure on the pump gauge. With the air pump attached to the shock valve, slowly cycle your shock through 25% of its travel 10 times as you reach your desired pressure. Rotate the CTD lever to the Descend mode (fully counter-clockwise).Slide your shocks sag setting o-ring up against the shock dust wiper.Unscrew the black air cap to expose the schrader valve.The bike comes with a fancy Fox Float RP23, 120mm travel. How much travel does a Fox Float RP23 have? Digressive compression tunes use preloaded valving to build compression quickly in order to give a firmer feel at low shaft speeds. Digressive force curves have been around long before bicycles had suspension. Propedal is a marketing term created by FOX to describe a digressive compression damping force curve. How do you turn the propedal knob on drcv?.What should the air pressure be on a float rp23 Fox?.How does the propedal knob work on a float?.How do you adjust the propedal Knob in rp23?.How much air should I put in my FOX shock?.How much travel does a Fox Float RP23 have?.